Summary of Common Faults for the Tannen T12 Ride-On Floor Scrubber

Tannen T12 The common faults and troubleshooting methods for ride-on floor scrubbers are as follows:

I. Issue of the brush disc not working

Possible causes and troubleshooting methods:

1、 Brush motor malfunction: Check whether the brush motor is damaged. You can do this by measuring the motor’s resistance or using a multimeter to verify whether the motor is functioning properly. If the motor is damaged, it needs to be replaced.

2、 Excessive ground resistance: Sometimes, if the ground is rough, the high resistance encountered during floor cleaning may cause the motor to trip. In such cases, you can try switching the circuit breaker on. If the problem persists, you’ll need to consider other potential factors.

3、 The brush disc is jammed by a foreign object: Check whether the brush disc is blocked by a foreign object, remove the foreign object, and then try restarting.

4、 Loose power plug: Check whether the power plug is loose or disconnected, and reinsert it firmly.

5、 Brush disc switch damaged: If the brush disc switch is damaged, you need to replace the faulty switch.

II. Poor water absorption: Doesn't absorb water cleanly or doesn't absorb water at all.

Possible causes and troubleshooting methods:

1、 Issue with the connection between the suction hose and the suction nozzle: Check whether the suction hose and the suction nozzle are free of debris or blockages, and ensure that the two are securely connected.

2、 Suction pipe blockage: Remove any foreign objects from the suction pipe to ensure it is completely unobstructed.

3、 Wear of the water-absorbing strip: Check whether the water-absorbing strip is severely worn. If it is severely worn, replace the strip promptly.

4、 Wear on the small wheels of the squeegee: If wear on the small wheels of the squeegee causes uneven contact with the ground, adjust the height of the squeegee’s small wheels to ensure they are in close contact with the surface.

5、 Sewage tank and float ball issues: Check whether the sewage tank is properly sealed and whether the float ball is blocking the motor inlet, thus preventing suction. If the float ball rises up and blocks the suction port, simply use your hand to press it down.

6、 Inlet motor failure: Check whether the inlet motor is functioning properly. If the motor is faulty, it needs to be repaired or replaced.

III. Power Supply Issues

Possible causes and troubleshooting methods:

1、 Make sure the power plug is securely inserted and check whether the power cord is damaged. A damaged power cord must be replaced promptly.

2、 A damaged power switch can also cause the machine to malfunction. If it’s damaged, it should be replaced promptly.

IV. The issue of the machine failing to start

Possible causes and troubleshooting methods:

1、 Check whether the battery has sufficient charge; if the charge is low, you’ll need to recharge it.

2、 Check whether the start switch is functioning properly; replace it promptly if the switch is damaged.

If none of the above is the problem, it could be that the circuit board has been damaged or short-circuited. In this case, you’ll need to seek assistance from a professional repair technician.

Five, The issue of excessive machine noise

Possible causes

1. The motor is not securely fixed.
2. There is a foreign object inside the machine.
3. Bearing wear.

Solution

1. Reattach the motor;
2. Clean out internal foreign objects;
3. Replace the worn bearings.

The above is for Tanen. T12 Here are some common solutions for typical malfunctions of ride-on floor scrubbers. If you encounter a complex or unsolvable issue, we recommend promptly contacting Tanen floor scrubber’s professional maintenance personnel for inspection and repair. In addition, regular maintenance and servicing of the machine are crucial for reducing breakdowns and extending its service life.

In summary, walk-behind floor scrubbers are widely used in industrial production and offer you... Efficient Convenient cleaning solutions. Our products boast powerful cleaning performance, outstanding operational and control features, and are suitable for a wide range of industrial environments. We are always committed to delivering superior product quality and an exceptional user experience. We look forward to providing you with a push-type floor scrubber that will leave you thoroughly satisfied, making your industrial production processes even more efficient. Efficient And cleaning. If you are interested in purchasing, please call: 13925069066 Manager Wu. http://www.meitengqi.com/ Guangzhou Qingqinyu Environmental Protection Technology Co., Ltd.

          Source of information: Guangzhou Qingqinyu Environmental Protection Technology Co., Ltd.

http://www.meitengqi.com/